SG-100M Electronic Hydrometer / Density Monitor / Meter
Model # SG-100M
The Eagle Eye SG-100M specific gravity meter/liquid density monitor can replace ordinary glass bulb and optical refractometer hydrometers that are limited in range, utility and functionality. The SG-100M has an in-tank, drop-hang submersible probe that measures, monitors, and records specific gravity/liquid density during a mixing, blending, fermentation, distillation, or plating operation. The SG-100M offers many user-customized options that allow the instrument to fit your exact measuring needs. The measurement probe can be purchased independently or for integration into an existing PLC (Programmable Logic Controller). Optional 4-20mA analog output board or dual 5 amp relays for automatic process control are also available. Cabling is either Teflon or PVC depending on the measuring sample.
The SG-100M is easy to use and versatile. Simply submerge the measuring probe up to 152 m (500 ft) and connect to an electronics module to provide digital readouts of user defined values such as Density, Specific Gravity, Baume, Brix, and Alcohol %. It can measure in liquids or slurries with an operating pressure range of 0 – 5 atm (operable in vacuum). The measurement probe is chemically resistant with PVC/Teflon wire strain relief and 316 stainless steel springs.
The Standard SG-100M Kit Includes:
- SG-100M Digital Panel Meter
- SG-100M Measurement Probe
- PVC Cable (Standard Lengths: 1.2 – 30.5 m( 4 –100 ft)
- User Manual
- Optional:Teflon Cable for Caustic Solutions
Custom packages allow the SG-100M to meet your system's requirements. The SG-100M measurement probe can be purchased as a stand alone piece to use within your system and PLC. Optional dual amp relays and 4-20mA output board are features that the SG-100M can be built with or without. The optional 4-20mA analog output allows for automatic process control, allowing you to continuously monitor and manage your solutions.At Eagle Eye we are proud to offer a range of products designed to save you in maintenance and replacement costs. See our selection of power solutions, including gas detectors, battery electrolyte level monitors, and more.
- Technical Specs
|Measurement Range(1)||Density: ±0.400 g/cm3 (within the range of|
0.550 lower limit to 2.000 g/cm3 upper limit)
Sample Temperature: 20 – 106 °C (40 – 220 °F)
|Pressure Range:||0 – 5 atm (operable in vacuum)|
|Min. Sample Volume:||310 mL|
|Data Transfer:||Analog Voltage Data Logger (optional) 4 – 20 mA, dual 5 A Relay|
|Operating Environment:||-20 – 106 °C (-40 – 220 °F)|
|Power Requirements:||Control Module: 120/240 VAC(3)|
Probe: 0 – 5 VDC
|Dimensions:||Probe Length x Diameter: 280 x 51 mm (11 x 2 in)|
|Weight:||Probe: 2.3 kg (5 lbs)|
|Cable Length:||Standard: PVC: 1.2 – 452.4 m (4 – 500 ft)|
Optional: Teflon: 1.2 – 30.4 m (5 – 200 ft)
Does the SG-100M need to be calibrated before use?
The SG-100M in-tank density meter has already been initialized at the factory using two benchmark liquids at room temperature of 72 °F (22 °C). The meter can be reinitialized (recalibrated) at any time at the user’s discretion.
How do I properly test using the SG-100M measurement probe?
The probe must be placed vertically upright (cable on top) in the liquid being tested and the liquid must cover the top of the cable connector on top of the probe for proper readings.
What is the range of densities the SG-100M can measure?
The SG-100M has been designed for use in the density range indicated on the attached label on the back of the meter (0.550 – 2.000 g/cm3). Measurements outside of this density range will not be valid.
How should the measurement probe be cleaned?
When the probe is used in water-soluble liquids, simply soaking in water and agitating should be sufficient for cleaning. If the probe needs to be completely dismantled for a more thorough cleaning, the probe-meter must be reinitialized after being reassembled.
What optional features can be bundled with the SG-100M digital hydrometer?
A 4-20mA analog output board or dual 5A relays are available for automatic process control, allowing you to continuously monitor and manage your solutions. Cabling included can be either Teflon or PVC depending on the measuring sample.
Can I purchase the measurement probe by itself? Yes, the SG-100M measurement probe can be purchased as a stand-alone piece to use within your system and integrate into an existing PLC (Programmable Logic Controller). The probe has a cable with a 3-wire connector at the end of the cable. The three wires are (black) ground, (red) power (5 VDC) and (green) signal (0- 5 VDC). The PLC engineer connects these wires to the PLC in his desired configuration.
How does the digital panel meter communicate? If you order the electronic module in addition to the probe, then the module powers the probe and it can provide a 4 - 20 ma analog output signal for PLC connection and control capabilities. This is the best option if your PLC is located at a longer distance from the probe.
- Measures in liquids or slurries
- Remote readout at desired distance from probe
- Readout can be chosen in preferred engineering units
- Battery or In-tank operation depending on application
- Determines concentration mix (by volume or mass) of the sample blend
- Large sample and operating temperature ranges (up to 106°C / 220°F)
- Easy to disassemble for cleaning
- Customization available based on user needs
- Flux Density Control
- Paper Production
Or call toll-free
Liquid Density Digital Electronic Hydrometer 0.550 – 2.000 g/cm3
Or call toll-free
To view a full list of our product videos, visit the video page.>